Thursday, October 3, 2019

History of the Mesopotamians

History of the Mesopotamians Mesopotamians Engineering is oldest and the most important science ever. As people continue to advance in life engineering became the only way to use and develop tools and processes needed for surviving and advancement in creativity of the human beings. Engineering includes many sciences such as the knowledge of mathematics, the applied science of chemistry and physics and is considered the master of all sciences and the origin of minor specialties. The Mesopotamians, one of the greatest and most ancient civilizations used engineering in their daily lives as they created the wheel and built water canals, and temples, also theyve had great advancements in architecture such as pyramid like structures and towers. More than 4000 years have passed since that civilization yet the most complex astronomical instruments are based on the invention of the revolutionary Astrolabe. The main aim of the device is to be used in astronomical observations; it consists of a graduated circular circles and a sighting arm and was based on the 60-unit numerical system used at that time. The greatest form of architecture created by the Mesopotamians is called the Ziggurat, a temple tower built to honour their gods and religious beliefs; it consists of a terraced pyramid of brick with steps, setbacks and a shrine at the top. Hammurabi, the king of Mesopotamians at that age assembled a system of laws that holds his name; it states that whoever builds poor structures should be penalized rightfully. Another Mesopotamians innovation is the Nahrwan, a 400 foot wide channel watering 200 miles of the land around. The Ancient Egyptians were the first civilization to master construction; they had specialists who were consultants to pharaohs and were identified as chiefs of works. At that time surveying, and irrigation systems were invented. The best architectural structure in history was left by the Egyptians which are The Great Pyramids, the first pyramid was built for the burial of Zoser, symbolizing absolute power, and it contained six mastabas to prevent thieves from access to the tomb and the surrounding artefacts. The largest Pyramid is Cheops its 481 feet high has a 13 acre base, above two million blocks of stone with standard mass of 2.5 tons were used, the inner stones weighed up to 30 tons. 100, 000 men working for 20 years, the stone blocks were glided down a special ramp, using wood rollers, ropes, and sledges. Greek Architects completed the progress to proficient stature, renowned as great construction professionals. The Greeks build great harbours overcoming any obstacles such as mountains, they were first to come with the ideas of artificial docks. In addition to their achievements is the Pharos lighthouse of Alexandria which was the first lighthouse ever built the Greek builder gathered wooden frames and levering devices that included capstans and pulleys. Romans have discovered hydraulic cement, achieving pile drivers, treadmill hoists and wooden bucket wheels. They constructed the Circus Maximus at which roman fighting games and contests took place. The Pantheon was a temple built by the outstanding ability of a Roman Engineer and it had a special height equal to its internal diameter. The middle ages are known for the great cathedrals, the enhancement of wind mills. The origin of the word Engineer is the Latin words In Generare which means to create. Engineers back then created war equipment such as catapults, and the discovery of gunpowder. Also the paper we use now was invented in the Far East. Some advanced Scientists made it easier for the advancement of engineering, such as Leonardo Da Vinci a unique artist, talented architect, and scientist has contributions to the field of abstract designs.

Wednesday, October 2, 2019

The Red Badge of Courage :: essays research papers

The Red Badge of Courage Henry Fleming, also called the youth, is the main character in The Red Badge of Courage. He decided to enlist in the army in hopes of gaining experience and being a part of the war. Although his mother was against him joining the army, Henry wanted the adventure and glory of being part of the war. Henry had many battles to fight within himself. He put off the facade that he was a very confident and strong soldier. But in actuality he was very unsure of himself. He always would question his own masculinity and whether or not he would run or fight in battle when the time came. Henry meets two men in is regiment that he calls the tall soldier and the loud soldier. They all go through the new experience of being in war together.   Ã‚  Ã‚  Ã‚  Ã‚  Later on when they get into battle Henry still has fears of fleeing the battle field. When the time comes to face the enemy Henry ended up running into the woods like many others. After he finds his way back to the regiment he sees what the battle has done to the soldiers. Many of his friends, including the tall soldier, died. Others were wounded. He in a way felt jealous because he didn’t have that wound, â€Å"red badge of courage† that they had to show. Henry continued on in the woods and came across a soldier. He tried to help him but the soldiers wouldn’t let him. In the disagreement the other soldier struck Henry with his gun. Henry went back to his camp and all of the men thought he had been wounded in the battle. He went along with this and many thought of him as brave.   Ã‚  Ã‚  Ã‚  Ã‚  The next day Henry had new insight and was not afraid of the battles.

Search for Innocence in American Modernism Essay -- Literature Essays

Search for Innocence in American Modernism      Ã‚   American Literature from its very beginning has been centered around a theme of innocence. The Puritans wrote about abandoning the corruption of Europe to find innocence in a new world. The Romantics saw innocence and power in nature and often wrote of escaping from civilization to return to nature. After the Civil War, however, the innocence of the nation is challenged. The Realists focused on the loss of innocence and in Naturalist works innocence is mostly gone. During these periods of American Literature it seems almost as if a hole was being dug, a sort of emptying of innocence, and after World War I the Modernists called this hole the wasteland Many Modernist works focus on society lost in the wasteland, but they hint at a way out. The path out of the wasteland is through a return to innocence. This is evident in the Modernist works of The wasteland by T. S. Eliot, "Directive" by Robert Frost, "Babylon Revisited" by F. Scott Fitzgerald, and "Hills Like White Elephants" by Earnest Hemingway as will be shown in an analysis of the inhabitants of the wasteland and their search for innocence, the role of children and pregnancy in the wasteland, and the symbolism of water and rebirth.    But before I go on, I believe that I should first clarify what I mean by "a return to innocence." First, there is some confusion between innocence and ignorance. They are often used interchangeably. Because a person is innocent, it does not mean that he or she is unaware of reality. Innocence is almost like a different type of view. A child and an adult may interpret a single thing entirely differently, but this does not mean that the adult knows more about that thing. Innocence is open ... ...ed society and only through the return of innocence can there be hope of anything better.    Works Cited Eliot, T.S. The wasteland. In The Heath Anthology of American Literature, Volume II. Edited by Paul Lauter et al. Lexington, MA: D.C. Heath and Company, 1991: 1447-1463.    Fitzgerald, F. Scott. "Babylon Revisited." In The Heath Anthology of American Literature, Volume II. Edited by Paul Lauter et al. Lexington, MA: D.C. Heath and Company, 1991: 1471-1485.    Frost, Robert. "Directive." In The Heath Anthology of American Literature, Volume II. Edited by Paul Lauter et al. Lexington, MA: D.C. Heath and Company, 1991: 1208-1209.    Hemingway, Ernest. "Hills Like White Elephants." In The Heath Anthology of American Literature, Volume II. Edited by Paul Lauter et al. Lexington, MA: D.C. Heath and Company, 1991: 1471-1485.      

Tuesday, October 1, 2019

Abortion Essay

Lucinda Seongbae Eng : Persuasive essay on abortion Prof. Fitzgerald A Positive View on Pro Abortion Abortion has been a controversy for many years and viewed in many different perspectives. Some individuals see it from a very positive point when this is being caused by the nature of the woman’s health, the age and others. It may also be seen as a way of getting rid of an unwanted or accidental pregnancy for reasons that are positive and beneficial for most women. According to feminist perspectives on reproduction and the family, in some cases abortion can be a positive act depending on the cause. For instance, in the case of a rape, health reasons or in the case of having an unwanted child for reasons of age, marital status, and economical reasons abortion is a potent tool to undo some mistakes. However, whichever ways it is perceived abortion gives a woman the right to choose and should not be viewed as a negative act but instead can be seen as a positive act in most circumstances. Based on the many positive reasons for abortion, abortion should be supported. Concerning the woman’s health an abortion can be performed when the woman cannot hold the fetus for health reasons. For example a woman who has AIDs and the fetus infected already can obtain an abortion because there is no life for the baby. Also a woman who has cancer at an advanced stage cannot keep a child in her womb or she will risk dying at birth. In the case of some diseases, kidney disease, severe hypertension, sickle-cell anemia, severe diabetes, etc that can be life threatening, an abortion often helps to avoid serious medical complications from childbirth. This also brings emphasis to Roe V. Wade (1973), which granted women the right to terminate an unwanted pregnancy, based on an implicit fundamental right to privacy and argued that it must be weighed against competing state interests in maternal safety and the protection of prenatal life; it protected this right during the first trimester of pregnancy (Thompson, 50). At this juncture the person has very good justifications of her action and is considered a positive act on her part. Another positive issue concerning abortion is a situation where girls below fifteen years are pregnant. In such situation abortion is possible because the girls are too young for child bearing. Also in situations where very young girls have little or no health facilities to ensure safe delivery, such as in developing countries, abortion is the only possible answer in order to avoid some major complication. According to researcher Mayor, complications from pregnancy and childbirth are the leading cause of death in young women aged fifteen to nineteen in developing countries. An estimated 70,000 adolescent mothers die each year because they have children before they are physically ready for parenthood, and more than 90% of these births are in developing countries the report says (www. bmjjournals. com). In this case, if a girl of these ages chooses to get an abortion to avoid complications of childbirth and/or death she is only making a positive decision for her life. According to those against abortion or those who perceive abortion as a negative act, one would argue that since life begins at conception, abortion is akin to murder as it is the act of taking human life. Abortion is in direct defiance of the commonly accepted idea of the sanctity of human life. In contrary, most abortions take place in the first trimester, when a fetus cannot exist independent of the mother. As it is attached by the placenta and umbilical cord, its health is dependent on her health, and cannot be regarded as a separate entity as it cannot exist outside her womb. Therefore, in this case abortion cannot be considered murder. According to Thomson (1971), â€Å"if women have rights over their own bodies, then they have rights not to have their bodies used by others against their will† (Thompson, 35-65). Therefore, even if it is argued that the fetus is a human life, the state has no right to force someone to donate use of their body to another person, even if that person is in extreme need. Another may argue that those who choose abortions are often minors or young women with insufficient life experience to understand fully what they are doing. Many have lifelong regrets afterwards. In defense to that, teenagers who become mothers have grim prospects for the future. They are much more likely to leave school; receive inadequate prenatal care; rely on public ssistance to raise a child; develop health problems; or end up divorced. Teenage births are associated with lower annual income for the mother. According to researcher Stanley, eighty percent of teen mothers must rely on welfare at some point. Teenage mothers are more likely to drop out of school. Only about one-third of teen mothers obtain a high school diploma. Teenage pregnancies are associated with increased rates of alcohol a nd substance abuse, and lower educational level (www. womenshealthchannel. com/teenpregnacy. index). In the modern world, abortions have become a norm of life and should not be looked upon as a negative act but an act of making a positive decision to undo some mistakes in life. Though women have been endowed with the gift of bearing a life form, an abortion gives them the option of whether they want to keep the present or not. However, an abortion should not be misunderstood for a convenience, as it does have its own advantages and disadvantages. The bigger picture that is being stressed is bodily integrity and self-ownership.

Monday, September 30, 2019

Types of Lies People Tell

TYPES OF LIES PEOPLE TELL Lies are part of human life. Nobody can deny that he or she has never lied before. Everybody lies. People start lying at around age 4 to 5 when they gain an awareness the power of language. Sometimes they can get away with lying, sometimes they can not. But everone knows that lying is a bad habit. Yet many people have no clue how big of a problem it is. Sadly, lying can become a destructive habit whatever your purpose is. According to the purpose to tell lies, they can be divided into three types; beneficial lies, spiteful lies , neutral lies.The first type of lies I find it good are beneficial lies. These lies usually mean to help and they are harmless that are meant to be tactful or polite. People prefer to tell it to protect the other people or not to make them unhappy. They help avoid hurt and sadness. For example, a father lie to the children that their beloved mother is living happily in heaven. People may think that this is a cheating, but they ought to praise these people who tell beneficial lies instead of criticizing them. The second type of lies are spiteful lies.These lies always mean to gain benefit and hurt people. People tell spiteful lies to protect themselves, look good,, gain financially or socially and avoid punishment. For example, as we usually see in supermarkets sellers lie to their customers to talk them into buying the fake foods. Their aims are only their personal gains, they do not care the other people. The third type of lies are neutral lies. These lies are just meant nothing and are much simpler. People tell these lies to not to Show their private things.For example, you asked a person about her private life or private things, she may avoid answering the truth by telling a lie. One hand, she does not want to share it with you, on the other hand she feels that she has to answer it, so she tells lie. Have you ever told any one of these lies? You may be able to lie for a while, but in the end it will come bac k to haunt you. It’s important to know that there is freedom in living and telling the truth. It may be difficult at first, but as we know, â€Å"The truth shall set you free. †

Sunday, September 29, 2019

Aircraft General Practices A320/321

SINGLE AISLE TECHNICAL TRAINING MANUAL MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES SINGLE AISLE TECHNICAL TRAINING MANUAL AIRCRAFT GENERAL PRACTICES 06 DIMENSIONS AND AREAS Structural Breakdown and Zoning (3) . . . . . . . . . . . . . . . . . . . . . . . . . 2 09 TOWING Towing with Nose Gear from the Front (2) . . . . . . . . . . . . . . . . . . . . 24 10 PARKING AND MOORING Parking and Mooring (2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 12 SERVICING Maintenance External Visit (3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 U3U06191 – U0O35M0MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES TABLE OF CONTENTS May 11, 2006 Page 1 SINGLE AISLE TECHNICAL TRAINING MANUAL STRUCTURAL BREAKDOWN AND ZONING (3) REFERENCE AXES The structure elements are installed according to the following reference axes. The X axis in the longitudinal direction of the fuselage, the Y axis in the dir ection of the wing span and the Z axis in the vertical direction. The cross section P presents a typical fuselage section at frame 47. NOTE: Note: The reference (station 0) for all structural measurements for the X axis is set at 100 in (254 cm) forward of the A/C nose.U3U06191 – U0O35M0 – UM01D1000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES STRUCTURAL BREAKDOWN AND ZONING (3) May 10, 2006 Page 2 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM01D1000000001 REFERENCE AXES MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES STRUCTURAL BREAKDOWN AND ZONING (3) May 10, 2006 Page 3 SINGLE AISLE TECHNICAL TRAINING MANUAL STRUCTURAL BREAKDOWN AND ZONING (3) ATA CHAPTERS The A/C structure is divided according to the ATA 100 specifications. SECTION NUMBERS Each major part of the A/C receives a section number. The fuselage section base number is 10.The fuselage is divided into various secti ons for manufacturing reasons. U3U06191 – U0O35M0 – UM01D1000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES STRUCTURAL BREAKDOWN AND ZONING (3) May 10, 2006 Page 4 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM01D1000000001 ATA CHAPTERS & SECTION NUMBERS MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES STRUCTURAL BREAKDOWN AND ZONING (3) May 10, 2006 Page 5 SINGLE AISLE TECHNICAL TRAINING MANUAL STRUCTURAL BREAKDOWN AND ZONING (3) SECTION NUMBERS (continued) WING AND TAIL PLANE The general wing section base number is 20.The general tail plane section base number is 30. U3U06191 – U0O35M0 – UM01D1000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES STRUCTURAL BREAKDOWN AND ZONING (3) May 10, 2006 Page 6 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM01D1000000001 SECTION NUMBERS – WING AND TAIL PLANE MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES STRUCTURAL BREAKDOWN AND ZONING (3) May 10, 2006 Page 7 SINGLE AISLE TECHNICAL TRAINING MANUAL STRUCTURAL BREAKDOWN AND ZONING (3) SECTION NUMBERS (continued) ENGINE, LANDING GEAR AND BELLY FAIRING The engine section base number is 40.The L/G section base number is 50. The general belly fairing section base number is 60. U3U06191 – U0O35M0 – UM01D1000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES STRUCTURAL BREAKDOWN AND ZONING (3) May 10, 2006 Page 8 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM01D1000000001 SECTION NUMBERS – ENGINE, LANDING GEAR AND BELLY FAIRING MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES STRUCTURAL BREAKDOWN AND ZONING (3) May 10, 2006 Page 9 SINGLE AISLE TECHNICAL TRAINING MANUAL STRUCTURAL BREAKDOWN AND ZONING (3) STATION NUMBERS FUSELAGEThe STAtion number is the distan ce in centimeters of a cross-section from a reference point. The station/frame numbers shown agree with the section boundaries. U3U06191 – U0O35M0 – UM01D1000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES STRUCTURAL BREAKDOWN AND ZONING (3) May 10, 2006 Page 10 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM01D1000000001 STATION NUMBERS – FUSELAGE MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES STRUCTURAL BREAKDOWN AND ZONING (3) May 10, 2006 Page 11 SINGLE AISLE TECHNICAL TRAINING MANUAL STRUCTURAL BREAKDOWN AND ZONING (3)STATION NUMBERS (continued) VERTICAL STABILIZER For the vertical stabilizer the reference station is Z=0 at the vertical Z-axis. Due to the fin tip extension, the A318 station numbers have changed. The new additional rib 12N is on the STA597. U3U06191 – U0O35M0 – UM01D1000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENER AL PRACTICES STRUCTURAL BREAKDOWN AND ZONING (3) May 10, 2006 Page 12 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM01D1000000001 STATION NUMBERS – VERTICAL STABILIZER MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES STRUCTURAL BREAKDOWN AND ZONING (3) May 10, 2006 Page 13SINGLE AISLE TECHNICAL TRAINING MANUAL STRUCTURAL BREAKDOWN AND ZONING (3) STATION NUMBERS (continued) HORIZONTAL STABILIZER, ENGINE AND WING For the horizontal stabilizer the reference station is y=0 at the A/C Y axis. For the wings, the reference station is the wing reference axis (WY). WY is located at 1868 mm (73. 54 in) from the A/C X axis. For the engines, station numbers are different depending on the version. U3U06191 – U0O35M0 – UM01D1000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES STRUCTURAL BREAKDOWN AND ZONING (3) May 10, 2006 Page 14 SINGLE AISLE TECHNICAL TRAINING MANUALU3U06191 – U 0O35M0 – UM01D1000000001 STATION NUMBERS – HORIZONTAL STABILIZER, ENGINE AND WING MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES STRUCTURAL BREAKDOWN AND ZONING (3) May 10, 2006 Page 15 SINGLE AISLE TECHNICAL TRAINING MANUAL STRUCTURAL BREAKDOWN AND ZONING (3) ZONES NUMBERS There are 8 major zones for the A/C. Each major zone is identified by the first digit of a three digits number. The even numbers identify the zones on the RH side of the A/C, while odd numbers identify the zones on the LH side of the A/C. The sub-zone 320 identifies the vertical stabilizer.U3U06191 – U0O35M0 – UM01D1000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES STRUCTURAL BREAKDOWN AND ZONING (3) May 10, 2006 Page 16 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM01D1000000001 ZONES NUMBERS MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES STRUCTURAL BREAKDOWN AND ZO NING (3) May 10, 2006 Page 17 SINGLE AISLE TECHNICAL TRAINING MANUAL STRUCTURAL BREAKDOWN AND ZONING (3) ZONES NUMBERS (continued) WING (UPPER SURFACE) AND HORIZONTAL STABILIZER The 500 numbers identify the LH wing zones, while the 600 numbers identify the RH wing zones.The sub-zones 330 and 340 identify the LH and RH side of the horizontal stabilizer. U3U06191 – U0O35M0 – UM01D1000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES STRUCTURAL BREAKDOWN AND ZONING (3) May 10, 2006 Page 18 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM01D1000000001 ZONES NUMBERS – WING (UPPER SURFACE) AND HORIZONTAL STABILIZER MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES STRUCTURAL BREAKDOWN AND ZONING (3) May 10, 2006 Page 19 SINGLE AISLE TECHNICAL TRAINING MANUAL STRUCTURAL BREAKDOWN AND ZONING (3)ZONES NUMBERS (continued) WING (LOWER SURFACE), BELLY FAIRING AND LANDING GEAR The sub-zone 7 10 identifies the NLG. The sub-zones 730 and 740 identify the LH and RH MLG. The sub-zone 190 indicates the belly fairing. 734 and 744 are the MLG door zone numbers. Access doors and panels are identified by the number of the zone in which the panel is installed followed by a two letter suffix. These two letters are used to indicate the doors and panels. The first letter indicates which access door or panel it is, starting from the reference axis (A=first, B=second, †¦ G=seventh, etc†¦ ). The second letter indicates the access door or panel location: – T=top (upper) surface, – B=bottom (lower) surface, – R=right side, – L=left side, – Z=internal, – F=floor panel, – W=sidewall panel, – C=ceiling panel. Here is an example of access panels on the left wing lower surface. U3U06191 – U0O35M0 – UM01D1000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES STRUCTURAL BREAKDOWN AND Z ONING (3) May 10, 2006 Page 20 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM01D1000000001ZONES NUMBERS – WING (LOWER SURFACE), BELLY FAIRING AND LANDING GEAR MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES STRUCTURAL BREAKDOWN AND ZONING (3) May 10, 2006 Page 21 SINGLE AISLE TECHNICAL TRAINING MANUAL STRUCTURAL BREAKDOWN AND ZONING (3) ZONES NUMBERS (continued) NACELLE, PYLON, ENGINE AND DOOR The difference between the LH and RH pylon and nacelle is made with the ten digits of the zone number 400. The difference between the LH side and RH side is identified by the last digit (Tens digit: odd for he left and even for the right).Within one engine, an odd zone number indicates the LH side and an even zone number indicates the RH side of the engine. The major zone 800 identifies the doors. U3U06191 – U0O35M0 – UM01D1000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES STRUCTURA L BREAKDOWN AND ZONING (3) May 10, 2006 Page 22 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM01D1000000001 ZONES NUMBERS – NACELLE, PYLON, ENGINE AND DOOR MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES STRUCTURAL BREAKDOWN AND ZONING (3) May 10, 2006 Page 23 SINGLE AISLE TECHNICAL TRAINING MANUALTOWING WITH NOSE GEAR FROM THE FRONT (2) TOWING WARNINGS AND CAUTIONS Obey the warning and cautions before, during and after to tow or pushback the A/C. U3U06191 – U0O35M0 – UM09D1000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES TOWING WITH NOSE GEAR FROM THE FRONT (2) May 10, 2006 Page 24 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM09D1000000001 TOWING – WARNINGS AND CAUTIONS MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES TOWING WITH NOSE GEAR FROM THE FRONT (2) May 10, 2006 Page 25 SINGLE AISLE TECHNICAL TRAIN ING MANUAL TOWING WITH NOSE GEAR FROM THE FRONT (2)TOWING (continued) TOWING WITH THE NOSE GEAR FROM THE FRONT This film describes how to push the A/C rearwards or tow the A/C forwards with the nose gear. The A/C may be towed or pushed back: – at maximum ramp weight, – with the engines shut down or running at idle. To begin the procedure, make sure: – that the safety devices are installed on the landing gears (L/G), – the wheel chocks are in place, – and check if the parking brake is ON. Do not tow the A/C if the dimension H is more than 300 mm (11. 8 in). If you do, you can cause damage to the internal centering cams of the nose landing gear (NLG).Referring to your A/C maintenance manual, make sure that the A/C is stable. Let us suppose that this procedure has been correctly done. During this procedure, depending on the configuration you are in, the A/C needs to be energized either by using the APU, a specific ground cart, an engine running, or by using the tractor itself. Let us suppose that the A/C is already energized and the EIS start procedure done. Outside, on the nose wheel steering deactivation electrical-box, set the ground-towing control lever to the towing position and install the pin. In the cockpit, – on the upper ECAM page, the â€Å"Nose.WHEEL STEERinG DISConnected† message comes into view on the memo page. – check on the Yellow brake-pressure triple-indicator that the accumulator pressure pointer is in the green range. We recommend pressurizing the yellow hydraulic system using the yellow electrical pump, thus, the braking system will be more efficient and safer. Now, we have to install the tow bar. MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES CAUTION: Caution: make sure that the tow bar has: – a damping system – a calibrated shear pin – two calibrated turn shear pins.This is to prevent high loads causing damage to the L/G. Refer to your A/C maintenance manual for the calibration of these pins. On the NLG, install the tow bar on the tow fitting and connect the tow bar to the tractor. CAUTION: Caution: put the parking brake control switch in the off position before you tow or push back the A/C. This is to prevent high loads causing damage to the NLG. On the Yellow brake-pressure triple-indicator, the brakes pressure pointers go down. In the cockpit, set the lighting system: – set the exterior light navigation and logo switch to ON. at night, set the interior light dome switch to bright and if the anti-collision lighting is necessary for the local airport regulations or the airline procedures, set the exterior light beacon switch to ON. On the VHF system: – in order to communicate with the control tower during towing operations, release out the VHF pushbutton switch and select the control tower frequency on the radio management panel. – in order to communicate with the ground mechanics, on the aud io control panel, set the interphone radio switch to the interphone position and release out the interphone reception pushbutton.For safety reasons, a distance of 3 meters (10 ft) must be kept clear around the nose wheels, tow bar and tractor when the aircraft moves. Towing speed limitation depends on the position of the passenger/crew and cargo doors. For these speed limitations refer to your A/C maintenance manual. TOWING WITH NOSE GEAR FROM THE FRONT (2) May 10, 2006 Page 26 U3U06191 – U0O35M0 – UM09D1000000001 SINGLE AISLE TECHNICAL TRAINING MANUAL The maximum permitted steering angle on each side of the A/C centerline is 95 degrees. When you use the front fittings to push the A/C rearwards with engine at idle this angle is limited to 40 degrees.At this point, be sure that all warnings and cautions of your A/C maintenance manual procedure and previous precautions are applied. Now, the A/C can be towed slowly and smoothly. Two other persons have to monitor the wing tips during the towing operation and one person is required in the cockpit in order to operate the brakes. When you complete the towing operation, make sure that the nose wheels are aligned with the A/C centerline. Inform the cockpit to apply the parking brake, and check that the parking brake light is ON on the nose wheel steering deactivation electrical-box.Put the wheel chocks in position. Disconnect the tow bar from the nose gear fittings. On the nose wheel steering deactivation electrical-box, remove the safety pin and set the ground-towing control lever to the normal position. At the same time, in the cockpit, on the ECAM memo display the message â€Å"N. WHEEL STEERG DISC† disappears. On the lighting system: – reset the exterior light beacon and navigation & logo switches to OFF. – reset the interior light dome switch to OFF. On the communication system: – cut the cockpit/control tower VHF link by pressing in the VHF pushbutton on the radio managem ent panel. reset the interphone radio switch to the neutral position. Depressurize the yellow hydraulic system, do the EIS stop procedure and de-energize the A/C electrical circuits. U3U06191 – U0O35M0 – UM09D1000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES TOWING WITH NOSE GEAR FROM THE FRONT (2) May 10, 2006 Page 27 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM09D1000000001 TOWING – TOWING WITH THE NOSE GEAR FROM THE FRONT MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES TOWING WITH NOSE GEAR FROM THE FRONT (2) May 10, 2006 Page 28SINGLE AISLE TECHNICAL TRAINING MANUAL This Page Intentionally Left Blank U3U06191 – U0O35M0 – UM09D1000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES TOWING WITH NOSE GEAR FROM THE FRONT (2) May 10, 2006 Page 29 SINGLE AISLE TECHNICAL TRAINING MANUAL TOWING WITH NOSE GEAR FROM THE FRONT (2) T AXIING AND ASSOCIATED PRECAUTIONS TURNING RADII The movement of the aircraft with its power on the ground is called taxi of the aircraft. During taxi of the aircraft, the minimum turning radii must be respected. U3U06191 – U0O35M0 – UM09D1000000001MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES TOWING WITH NOSE GEAR FROM THE FRONT (2) May 10, 2006 Page 30 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM09D1000000001 TAXIING AND ASSOCIATED PRECAUTIONS – TURNING RADII MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES TOWING WITH NOSE GEAR FROM THE FRONT (2) May 10, 2006 Page 31 SINGLE AISLE TECHNICAL TRAINING MANUAL TOWING WITH NOSE GEAR FROM THE FRONT (2) TAXIING AND ASSOCIATED PRECAUTIONS (continued) DANGER AREAS Safety precautions must be taken to avoid danger from engine suction and exhaust areas.Access to the engine is only allowed through the entry corridor. Note that the entry c orridor must be closed for wind directions greater than 90?. There is no safe access corridor when the engine is running above minimum idle. Depending on the distance from the running engine and on its power setting, it is necessary to wear ear protection and to respect the maximum time exposure. U3U06191 – U0O35M0 – UM09D1000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES TOWING WITH NOSE GEAR FROM THE FRONT (2) May 10, 2006 Page 32 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM09D1000000001TAXIING AND ASSOCIATED PRECAUTIONS – DANGER AREAS MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES TOWING WITH NOSE GEAR FROM THE FRONT (2) May 10, 2006 Page 33 SINGLE AISLE TECHNICAL TRAINING MANUAL PARKING AND MOORING (2) GENERAL This module covers the following subjects of the aircraft: – parking, not more than 2 days, – storage, – and mooring of the landing gear s. The module is destined to cover the entire Single Aisle Airbus family, which includes the A318, A319, A320 and A321 airplanes. – Open the cockpit and cabin window shades. Make sure that the sliding windows are closed. Installation of the Protection Equipment: Protect all the probes, the engines and the APU with adapted protection equipment. – On the overhead panel 25VU, on the CABIN PRESS section, push the DITCHING pushbutton switch to close the ventilation skin valves and the outflow valves. PARKING (NOT MORE THAN 2 DAYS) This section gives the procedure to park the aircraft in standard weather conditions but: – if the aircraft is parked in high wind conditions, a check of the aircraft stability is needed, and moor the aircraft if necessary, – if the aircraft is parked in cold weather conditions, do the cold weather maintenance procedures.PARKING PROCEDURE To park the aircraft follow these tasks: – If necessary, clean the aircraft. – Par k the aircraft on a flat surface. Make sure that the wheels of the nose landing gear are on the aircraft axis and the aircraft points into the wind. – Install the safety devices on the landing gears. – Make sure that the flight control surfaces are retracted. – Put the wheel chocks in position: – for the NLG, in front of and behind the wheels, – for the MLG, in front of and behind wheels. – Ground the aircraft. – If necessary refuel the fuel tanks to 30% minimum of their total capacity. Drain water from all the fuel tanks. MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES PARKING AND MOORING (2) May 10, 2006 Page 34 U3U06191 – U0O35M0 – UM10D1000000001 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM10D1000000001 GENERAL & PARKING (NOT MORE THAN 2 DAYS) MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES PARKING AND MOORING (2) May 10, 2006 Page 35 SINGLE AISLE TECHNICAL TRAINING MANUAL PARKING AND MOORING (2) STORAGE PROCEDURE Certain maintenance tasks must be performed to prepare the aircraft for storage. See AMM.During the storage period, periodic ground checks must be performed. See AMM. Certain tasks must be performed to return the aircraft to operation after the storage. See AMM. U3U06191 – U0O35M0 – UM10D1000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES PARKING AND MOORING (2) May 10, 2006 Page 36 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM10D1000000001 STORAGE PROCEDURE MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES PARKING AND MOORING (2) May 10, 2006 Page 37 SINGLE AISLE TECHNICAL TRAINING MANUAL PARKING AND MOORING (2) MOORING OF THE AIRCRAFTThe purpose of mooring is to prevent damage to the aircraft on the ground in high wind conditions. For wind speeds less than 50 kts: – mooring is not necessar y if the aircraft configuration is in the limits given in chapter 05-57-00. If the aircraft points into the wind and wind speed is: – between 50 and 70 Kts, moor the aircraft at the NLG, – more than 70 Kts, moor the aircraft at the NLG and MLG. If the aircraft does not point into the wind or the direction of the wind is not stable: – for wind speeds or gusts more than 50 Kts, moor the aircraft at the NLG and the MLG. U3U06191 – U0O35M0 – UM10D1000000001MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES PARKING AND MOORING (2) May 10, 2006 Page 38 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM10D1000000001 MOORING OF THE AIRCRAFT MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES PARKING AND MOORING (2) May 10, 2006 Page 39 SINGLE AISLE TECHNICAL TRAINING MANUAL MAINTENANCE EXTERNAL VISIT (3) PRESENTATION This film presents the A321 outside safety inspection and cockpit Ch eck-List (CL) to be performed before powering the A/C for maintenance purposes. Various main stations have been defined. The inspection starts with the nose tation. First verify that the NLG chocks are in place. Then, observe that the NLG doors are closed. Make sure that the NLG safety pin is installed. The NLG steering pin must be as required. Finally, verify that the A/C is electrically grounded. The second step consists of inspecting the right MLG. Start by checking that the MLG door is closed. Then, verify that the MLG safety sleeve is installed. Lastly, observe that the MLG chocks are in place. Let us continue with the right engine station, the first thing to do is to make sure that the engine right side access doors are secured. The same must be done for the left side.Check that the engine fan cowls and thrust reverser cowls are secured. The right wing is the 4th station. Observe the position of the slats and then, the flaps. The spoilers must be retracted. Then move to the le ft wing station. Here again observe the position of the flaps and then, the slats. Although make sure that the spoilers are retracted. The next step is the left engine station. Check that the engine right side access doors are secured. Then pass around the engine to verify that the left side access doors are secured. Make sure that the engine fan cowls and thrust reverser cowls are secured. Proceed with the left MLG station.The Ram Air Turbine (RAT) safety device must be in the stowed position. Continue by checking that the MLG door is closed and that the MLG safety sleeve is installed. Before moving on, observe that the MLG chocks are in place. In the A/C area station you have to make sure that the A/C area is clean and clear of tools and any other items. Now you have to check the 9th station: the external power receptacle. Verify that the external power is connected and available. Finally enter the cockpit for the last station. Start by checking the rear and the overhead circuit b reaker, then have a look to the emergency equipment.This consists in: verifying that the MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES U3U06191 – U0O35M0 – UM01D4000000001 escape ropes are present, observing that the fire extinguisher is in position, making sure that the cockpit is equipped with smoke hoods, checking that the fire protective gloves are present, ensuring the crash axe is in position, checking that the cockpit is equipped with life vest, verifying that the oxygen masks are present, observing that the flash lights are in position. You must then make sure that the wipers are off. BATtery 1 and 2 P/BSW must be off and their voltage should be about 25 volts.Proceed by setting the BAT1 P/BSW to AUTO. Then, set the BAT2 P/BSW to AUTO, check that the right hand dome light is on. Verify that the speed brake handle is in the RETract disarm position. If the speed brake handle disagrees with the surface position maintenance action is du e. On the center pedestal make sure that the thrust levers are in the idle position. Engine master switches 1 and 2 must be in the OFF position and the engine ignition mode selector in the NORMal position. Observe that the flap handle is set according to surface position. If engine reverse cowls have to be opened for maintenance action, the slats must to be retracted.Still on the center pedestal, check that the radar is off, also verify that the ATC transponder is off. Make sure that the gravity gear extension crank handle is in the reset stowed position. On the instrument panel observe that the three green triangles on the LanDinG GEAR panel are on. The control safety check list should now have been accomplished. On the overhead panel set the EXTernal PoWeR P/BSW to ON, also set the GENerator 1 P/BSW to on and the GEN2 P/SW to ON. Scan and check that no amber lights are on except GEN1 and 2 FAULT light on panel 44VU. The GALY & CAB P/BSW should be as required.Finally verify that th ere is no light on the VENTilation panel. The A/C is now ready for maintenance. NOTE: This film shows an A321 but the procedure is also valid for A318, A319 and A320 aircrafts. MAINTENANCE EXTERNAL VISIT (3) May 10, 2006 Page 40 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM01D4000000001 PRESENTATION MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES MAINTENANCE EXTERNAL VISIT (3) May 10, 2006 Page 41 SINGLE AISLE TECHNICAL TRAINING MANUAL MAINTENANCE EXTERNAL VISIT (3) STEP BY STEP The following topics develop step by step the previous film presentation.NOSE STATION AND EXTERNAL POWER RECEPTACLE To the station 1, in first, verify that the NLG chocks are in place. Then, observe that the NLG doors are closed. Make sure that the NLG safety pin is installed. The steering pin must be as required. Finally, verify that the A/C is electrically grounded. NOTE: Note: The A/C can also be grounded from the MLG. For the station 9, verify tha t the external power is connected and available. U3U06191 – U0O35M0 – UM01D4000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES MAINTENANCE EXTERNAL VISIT (3) May 10, 2006 Page 42 SINGLE AISLE TECHNICAL TRAINING MANUALU3U06191 – U0O35M0 – UM01D4000000001 STEP BY STEP & NOSE STATION AND EXTERNAL POWER RECEPTACLE MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES MAINTENANCE EXTERNAL VISIT (3) May 10, 2006 Page 43 SINGLE AISLE TECHNICAL TRAINING MANUAL MAINTENANCE EXTERNAL VISIT (3) RIGHT AND LEFT MLG STATION The station 2 and 7 consist of inspecting the Right (R) and Left (L) MLG. Start by checking that the MLG door is closed. Then, verify that the MLG safety sleeve is installed. Finally, observe that the MLG chocks are in place. To the left station, the Ram Air Turbine (RAT) stowed position safety device must be installed.U3U06191 – U0O35M0 – UM01D4000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES MAINTENANCE EXTERNAL VISIT (3) May 10, 2006 Page 44 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM01D4000000001 RIGHT AND LEFT MLG STATION MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES MAINTENANCE EXTERNAL VISIT (3) May 10, 2006 Page 45 SINGLE AISLE TECHNICAL TRAINING MANUAL MAINTENANCE EXTERNAL VISIT (3) RIGHT AND LEFT ENGINE STATION RIGHT AND LEFT ENGINE SIDE ACCESS DOORS On station 3, the first thing to do is to make sure that the engine right and left side access doors are secured.The same must be done on station 6. U3U06191 – U0O35M0 – UM01D4000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES MAINTENANCE EXTERNAL VISIT (3) May 10, 2006 Page 46 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM01D4000000001 RIGHT AND LEFT ENGINE STATION – RIGHT AND LEFT ENGINE SIDE ACCESS DOORS MAINTENANCE COURS E – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES MAINTENANCE EXTERNAL VISIT (3) May 10, 2006 Page 47 SINGLE AISLE TECHNICAL TRAINING MANUAL MAINTENANCE EXTERNAL VISIT (3)RIGHT AND LEFT ENGINE STATION (continued) ENGINE FAN COWLS AND THRUST REVERSER COWLS Check that the engine fan cowls and thrust reverser cowls are secured. U3U06191 – U0O35M0 – UM01D4000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES MAINTENANCE EXTERNAL VISIT (3) May 10, 2006 Page 48 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM01D4000000001 RIGHT AND LEFT ENGINE STATION – ENGINE FAN COWLS AND THRUST REVERSER COWLS MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES MAINTENANCE EXTERNAL VISIT (3) May 10, 2006 Page 49 SINGLE AISLE TECHNICAL TRAINING MANUALMAINTENANCE EXTERNAL VISIT (3) RIGHT AND LEFT WING STATION The R and L wing are the 4 and 5 stations. Confirm the position of the slats and then, t he flaps. The spoilers must be retracted. U3U06191 – U0O35M0 – UM01D4000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES MAINTENANCE EXTERNAL VISIT (3) May 10, 2006 Page 50 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM01D4000000001 RIGHT AND LEFT WING STATION MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES MAINTENANCE EXTERNAL VISIT (3) May 10, 2006 Page 51 SINGLE AISLE TECHNICAL TRAINING MANUAL MAINTENANCE EXTERNAL VISIT (3)AIRCRAFT AREA In the A/C area station 8, you have to make sure that the A/C area is clean and clear of tools, other items and FOD. U3U06191 – U0O35M0 – UM01D4000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES MAINTENANCE EXTERNAL VISIT (3) May 10, 2006 Page 52 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM01D4000000001 AIRCRAFT AREA MAINTENANCE COURSE – CAT A (V2500-A5/ME) AI RCRAFT GENERAL PRACTICES MAINTENANCE EXTERNAL VISIT (3) May 10, 2006 Page 53 SINGLE AISLE TECHNICAL TRAINING MANUAL MAINTENANCE EXTERNAL VISIT (3) COCKPIT STATION REAR AND OVERHEAD C/B PANELSStart by checking that the rear C/Bs and the overhead C/Bs are in closed position. U3U06191 – U0O35M0 – UM01D4000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES MAINTENANCE EXTERNAL VISIT (3) May 10, 2006 Page 54 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM01D4000000001 COCKPIT STATION – REAR AND OVERHEAD C/B PANELS MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES MAINTENANCE EXTERNAL VISIT (3) May 10, 2006 Page 55 SINGLE AISLE TECHNICAL TRAINING MANUAL MAINTENANCE EXTERNAL VISIT (3) COCKPIT STATION (continued) EMERGENCY EQUIPMENTThen, have a look the emergency equipment. This consists in verifying that the escape ropes are present, observing that the fire extinguisher is in position, making sure that the cockpit is equipped with smoke hoods, checking that the fire protective gloves are present, ensuring that the crash axe is in position, checking that the cockpit is equipped with life vests, verifying that the oxygen masks are present and observing that the flash lights are in position. U3U06191 – U0O35M0 – UM01D4000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES MAINTENANCE EXTERNAL VISIT (3)May 10, 2006 Page 56 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM01D4000000001 COCKPIT STATION – EMERGENCY EQUIPMENT MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES MAINTENANCE EXTERNAL VISIT (3) May 10, 2006 Page 57 SINGLE AISLE TECHNICAL TRAINING MANUAL MAINTENANCE EXTERNAL VISIT (3) COCKPIT STATION (continued) PEDESTAL PANEL CHECK LIST On the center pedestal, verify that the speed brake handle is in the retract/disarm position. If the speed brake handle disa grees with the surface position, maintenance action is due. Make sure that the thrust levers are in the IDLE position.ENG MASTER SWs 1 and 2 must be in the OFF position and the engine ignition mode selector in the NORMal position. Observe that the flap handle is set according to surface position. If engine reverser cowls have to be opened for maintenance action, the slats must be retracted. Check that the radar is off. Also, verify that the Air Traffic Control (ATC) transponder is off. Make sure that the gravity gear extension handle is in the reset and stowed position. U3U06191 – U0O35M0 – UM01D4000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES MAINTENANCE EXTERNAL VISIT (3) May 10, 2006 Page 58SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM01D4000000001 COCKPIT STATION – PEDESTAL PANEL CHECK LIST MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES MAINTENANCE EXTERNAL VISIT (3) May 10, 2006 Page 59 SINGLE AISLE TECHNICAL TRAINING MANUAL MAINTENANCE EXTERNAL VISIT (3) COCKPIT STATION (continued) OVERHEAD PANEL CHECK LIST AND A/C POWER SUPPLY You must then make sure that the wipers are off. BATteries 1 & 2 P/BSWs must be OFF and the voltage should be about 25 volts. Proceed by setting the BAT 1 P/BSW to AUTO position. Then, set the BAT 2 P/BSW to AUTO position.NOTE: Note: if BAT voltage is below 25V, a charging cycle of 20 minutes is required. Check that the right hand dome light is on. A/C power supply procedure: On the overhead panel, set the EXTernal PoWeR P/BSW to ON. Also, set the GEN 1 P/BSW to ON and the GEN 2 P/BSW to ON. Scan and check that no amber lights are on except GENerator (GEN) 1 and GEN 2 FAULT lights on panel 35VU. The GALY & CAB P/BSW should be as required. Finally, verify there is no light on the ventilation panel. The A/C is now ready to maintenance. U3U06191 – U0O35M0 – UM01D4000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICESMAINTENANCE EXTERNAL VISIT (3) May 10, 2006 Page 60 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM01D4000000001 COCKPIT STATION – OVERHEAD PANEL CHECK LIST AND A/C POWER SUPPLY MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES MAINTENANCE EXTERNAL VISIT (3) May 10, 2006 Page 61 SINGLE AISLE TECHNICAL TRAINING MANUAL MAINTENANCE EXTERNAL VISIT (3) COCKPIT STATION (continued) MAIN INSTRUMENT PANEL CHECK LIST AND CONTROLS SAFETY CHECK LIST COMPLETED On the instrument panel, make sure that the L/G lever is in the down position and confirm that the three green arrows on the L/G panel are on.The control safety CL should now have been accomplished. U3U06191 – U0O35M0 – UM01D4000000001 MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES MAINTENANCE EXTERNAL VISIT (3) May 10, 2006 Page 62 SINGLE AISLE TECHNICAL TRAINING MANUAL U3U06191 – U0O35M0 – UM01D4000000001 COCKPIT STATION – MAIN INSTRUMENT PANEL CHECK LIST AND CONTROLS SAFETY CHECK LIST COMPLETED MAINTENANCE COURSE – CAT A (V2500-A5/ME) AIRCRAFT GENERAL PRACTICES MAINTENANCE EXTERNAL VISIT (3) May 10, 2006 Page 63

Saturday, September 28, 2019

Barriers to Effective Communication Paper

Barriers to Effective Communication Paper Tametrius Walker Mrs. Alsup CJA 363 February 2, 2011 In this paper I will be discussing the process of communication and its components, discuss the difference between listening and hearing in communication, talk about the formal and informal channels of communication, talk about the different barriers to effective communication, and lastly discuss the strategies that may be implemented to overcome communication barriers. Communication is very crucial in the criminal justice system; it is the key element for success. From a rookie all the way up to a chief, every police officer must be able to speak, listen, and understand without excuses. There is no room for poor communication in the criminal justice system, because it is a waste of time and a waste of everyone’s energy. An author named A. Richard in 1928 gave the best definition of communication he said, â€Å"Communication takes place when one mind acts upon its environment and that another mind is influenced. In that other mind an experience occurs just like the experience in the first mind, and is caused by that experience† [(Wallace, 2009)]. Communication is not an isolated event, it is a process. It is five steps that the communication process contains and it is transmitting an idea, sending the idea through a medium, receiving the message, understanding the idea, and providing feedback to the message sender. The communication process becomes flawed, when failure occurs during any of the five steps, and the information that is at hand will not flow in a smooth and accurate manner. The first step to communication is transmitting an idea. This step is the information of several thoughts and the desire to express the ideas. Sending the idea through a medium, which is the second step means that the message needs to be sent once it is formed. Transmitting an idea can be done in writing, orally, or by action. Each method is interpreted in a different way, no matter what medium is used to send a message. The critical part of communication is receiving the message. This is the reverse of message transmission. In order for the message to be effective, it must be received and acted on. An important part of communication understands the idea. What is the point of transmitting the idea in the first place, if nobody can comprehend the message? The sender should always take into consideration the person or people that are receiving the information before the message is even sent, putting themselves into receiver’s shoes so that that the essence of the idea is communicated. Providing feedback for the message sender is the last step in the communication process. The communication loop comes to an end, when this step occurs. At this point the recipient let the sender know if the information that was received was understood or needs clarification. Exchanging information that involves at least two people is the primary reason for communication. The communication process is the essence of our lives and how we get everything we do across to the rest of the world that is why it is so important. There are two steps when it comes to communication. Step one is hearing and step two is listening. Both of these words are different. In order for the communication process to be successful you have to hear first and then listen. Hearing is when a person ear picks up sound waves and then sends it to the brain. Listening which is the active process is the second part of communication. You need to be an active participant in other words. The active listener not only evaluates the message before they respond, they also think as the speakers relay the message. The thought speed of listeners is a lot faster than the speaking speed of listeners, which will result in lagging and may lead to day dreaming. A listener must concentrate on the message so that they may become an active listener to be successful in communication to overcome this. The traditional communication method in an organization most of the time is formal and informal. In formal communication this channel follows the chain of command, which is typified by detectives, formal orders, and written memorandums. These forms provide order and security. The use of excessive and exclusive communications has certain disadvantages. Strict adherence to formal channels can be personal and time consuming, this is one disadvantage. Memorandums must go through the chain of command, then forwarded to the right personnel in order to be drafted carefully. It will also require written records and a lot of people do not like putting their information on paper because it will restrict the flow of the written information, this is another drawback of formal channels. Formal communications also have advantages, however. Formal communication makes it easy for officers because the new information that are about crimes that need to be given to all officers, can make the situation critical, then formal communication is very clear and less confusing regarding the contents. Informal channels which is departmental gossip. This is used between detectives and patrol officers. Using informal channels can save time when time is critical. Instead of going through the entire process, informal channel allows an officer to take the short cut and pass the information on quickly and responsibly. It is also used so different departments can share information. For instance, if a robbery crime resulted in a homicide. This situation allows both departments to team up and solve the crime. When it comes to barriers to effective communication, there are four different types; they are emotional barriers, physical barriers, semantic barriers, and ineffective listening. An emotional barrier means that everyone takes a situation in their own way. Emotional barriers happens in the sender or receiver of a message, majority of the time an individual will let their experiences get in the way while transmitting or receiving information. Examples include fear, anger, and hostility. A physical barrier is anything that allows the free flow of information difficult. A semantic barrier is studying the meaning and development of words. For instance, officers interpret juvenile delinquent in different ways such as youth acting out, hard core, or under age youth. It can result in bad communication having the inability to understand one another. Ineffective listening which is the last barrier is failure to receive or hear another individual message. There are many strategies that may be implemented to overcome communication barriers. When it comes down to emotional problems peer support system will help because this allows officers to work with one another to solve roblems. When addressing physical barriers, not allowing anything to slow down the flow of information will overcome communication barriers. If semantic barriers are guarded against it will help officers to agree on the meaning of terms, which will help them to effectively communicate. Lastly, I think the best way to overcome communication barriers is to help people improve their listening skills. It will help the criminal justice department if officers will use these strategies because it will overcome all their barriers to communicate. As you have read communication is very important. In every aspect of the criminal justice system, it is the key element for success. Not only will it better ourselves as officers, with these skills of communications, but we can also strive for better goals which will not only help the department, but also the judicial system and our communities. We can overcome barriers and encourage others that are striving to do the same, As long as we push forward and follow these strategies. Reference Harvey Wallace J. D. , C. R. (2009). Oral and written communication